Categories
LED BULB
LED DOWNLIGHT
Correct maintenance steps for Tri Proof Led Light
1. The dust and dirt on the shell and tube of the Tri Proof Led Light should be cleaned regularly. Note that if there is water mist in the lamp cavity of the Tri Proof Led Light used in a humid environment, it should be removed in time to avoid rust damage or damage over time. The phenomenon of leakage and short circuit.
2. Check whether the transparent parts of the luminaire are impacted by foreign matter, and whether the protective net is loose, desoldering, corrosion, etc. If so, stop using it and repair and replace it in time.
3. The damage of the light source of the Tri Proof Led Light should be replaced in time to prevent the electric components such as the ballast from being in an abnormal state for a long time due to the failure of the light source to start the lamp.
4. When opening the lampshade of the Tri Proof Led Light, you should cut off the power supply and open the cover according to the requirements of the warning sign. After opening the cover, check whether the flameproof bonding surface of the Tri Proof Led Light is intact, whether the rubber seal is abnormal, whether the wire insulation layer is green and carbonized, whether the insulation and electrical components are deformed and scorched. If there are such problems, they should be repaired and replaced in time.
5. Try not to switch frequently when using the lamp, because the current through the filament is greater than the current during normal operation when the lamp is frequently started, which makes the temperature of the filament rise sharply and accelerate sublimation, which will greatly reduce its service life. To minimize the switch of lamps and lanterns.
LED DOWNLIGHT
Correct maintenance steps for Tri Proof Led Light
1. The dust and dirt on the shell and tube of the Tri Proof Led Light should be cleaned regularly. Note that if there is water mist in the lamp cavity of the Tri Proof Led Light used in a humid environment, it should be removed in time to avoid rust damage or damage over time. The phenomenon of leakage and short circuit.
2. Check whether the transparent parts of the luminaire are impacted by foreign matter, and whether the protective net is loose, desoldering, corrosion, etc. If so, stop using it and repair and replace it in time.
3. The damage of the light source of the Tri Proof Led Light should be replaced in time to prevent the electric components such as the ballast from being in an abnormal state for a long time due to the failure of the light source to start the lamp.
4. When opening the lampshade of the Tri Proof Led Light, you should cut off the power supply and open the cover according to the requirements of the warning sign. After opening the cover, check whether the flameproof bonding surface of the Tri Proof Led Light is intact, whether the rubber seal is abnormal, whether the wire insulation layer is green and carbonized, whether the insulation and electrical components are deformed and scorched. If there are such problems, they should be repaired and replaced in time.
5. Try not to switch frequently when using the lamp, because the current through the filament is greater than the current during normal operation when the lamp is frequently started, which makes the temperature of the filament rise sharply and accelerate sublimation, which will greatly reduce its service life. To minimize the switch of lamps and lanterns.
Correct maintenance steps for Tri Proof Led Light
1. The dust and dirt on the shell and tube of the Tri Proof Led Light should be cleaned regularly. Note that if there is water mist in the lamp cavity of the Tri Proof Led Light used in a humid environment, it should be removed in time to avoid rust damage or damage over time. The phenomenon of leakage and short circuit.
2. Check whether the transparent parts of the luminaire are impacted by foreign matter, and whether the protective net is loose, desoldering, corrosion, etc. If so, stop using it and repair and replace it in time.
3. The damage of the light source of the Tri Proof Led Light should be replaced in time to prevent the electric components such as the ballast from being in an abnormal state for a long time due to the failure of the light source to start the lamp.
4. When opening the lampshade of the Tri Proof Led Light, you should cut off the power supply and open the cover according to the requirements of the warning sign. After opening the cover, check whether the flameproof bonding surface of the Tri Proof Led Light is intact, whether the rubber seal is abnormal, whether the wire insulation layer is green and carbonized, whether the insulation and electrical components are deformed and scorched. If there are such problems, they should be repaired and replaced in time.
5. Try not to switch frequently when using the lamp, because the current through the filament is greater than the current during normal operation when the lamp is frequently started, which makes the temperature of the filament rise sharply and accelerate sublimation, which will greatly reduce its service life. To minimize the switch of lamps and lanterns.
Correct maintenance steps for Tri Proof Led Light
1. The dust and dirt on the shell and tube of the Tri Proof Led Light should be cleaned regularly. Note that if there is water mist in the lamp cavity of the Tri Proof Led Light used in a humid environment, it should be removed in time to avoid rust damage or damage over time. The phenomenon of leakage and short circuit.
2. Check whether the transparent parts of the luminaire are impacted by foreign matter, and whether the protective net is loose, desoldering, corrosion, etc. If so, stop using it and repair and replace it in time.
3. The damage of the light source of the Tri Proof Led Light should be replaced in time to prevent the electric components such as the ballast from being in an abnormal state for a long time due to the failure of the light source to start the lamp.
4. When opening the lampshade of the Tri Proof Led Light, you should cut off the power supply and open the cover according to the requirements of the warning sign. After opening the cover, check whether the flameproof bonding surface of the Tri Proof Led Light is intact, whether the rubber seal is abnormal, whether the wire insulation layer is green and carbonized, whether the insulation and electrical components are deformed and scorched. If there are such problems, they should be repaired and replaced in time.
5. Try not to switch frequently when using the lamp, because the current through the filament is greater than the current during normal operation when the lamp is frequently started, which makes the temperature of the filament rise sharply and accelerate sublimation, which will greatly reduce its service life. To minimize the switch of lamps and lanterns.
2. Check whether the transparent parts of the luminaire are impacted by foreign matter, and whether the protective net is loose, desoldering, corrosion, etc. If so, stop using it and repair and replace it in time.
3. The damage of the light source of the Tri Proof Led Light should be replaced in time to prevent the electric components such as the ballast from being in an abnormal state for a long time due to the failure of the light source to start the lamp.
4. When opening the lampshade of the Tri Proof Led Light, you should cut off the power supply and open the cover according to the requirements of the warning sign. After opening the cover, check whether the flameproof bonding surface of the Tri Proof Led Light is intact, whether the rubber seal is abnormal, whether the wire insulation layer is green and carbonized, whether the insulation and electrical components are deformed and scorched. If there are such problems, they should be repaired and replaced in time.
5. Try not to switch frequently when using the lamp, because the current through the filament is greater than the current during normal operation when the lamp is frequently started, which makes the temperature of the filament rise sharply and accelerate sublimation, which will greatly reduce its service life. To minimize the switch of lamps and lanterns.