Categories
LED BULB
LED DOWNLIGHT
Installation method and disassembly and replacement of embedded downlight | Square Recessed Downlights
At present, many living rooms are equipped with recessed downlights. However, it is inevitable to change the recessed downlight after a long time, but many people don't know what to do. Today, Houjiji will share with you how to install and disassemble the recessed downlight. Let's take a look at them.
1. Installation method of embedded downlight:
1. Check the indication of the embedded downlight, determine the size of the embedded downlight, and mark the opening position of the ceiling.
2. According to the size of the opening, use a measuring device to draw a circular mark on the ceiling and use a small hand saw to make the opening. This step requires a certain skill, otherwise it is easy to damage the ceiling.
3. Connect the power cord reserved on the ceiling to the recessed downlight according to the electricity specification.
4. Adjust the wing nut fixing the embedded downlight spring so that the height of the embedded downlight spring is equal to the thickness of the ceiling, and then put the embedded downlight spring buckle vertically into the open ceiling hole.
5. The spring buckles on both sides of the recessed downlight are extended and clamped on the back of the ceiling. Finally, replace the bulb to complete the installation of the embedded downlight.
How do I remove and replace the recessed downlight
1. When disassembling the electricity, disconnect the leakage switch and pay attention to the safety of electricity.
2. Remove the embedded downlight to prevent damage during removal.
3. According to the installation method of the embedded downlight mentioned above, it can be seen that the embedded downlight is fixed with a spring buckle and a barb, as long as the embedded downlight is pulled down and removed.
4. Disconnect the built-in downlight from the power supply, and replace the built-in downlight according to the above installation method.
Square Recessed Downlights
LED DOWNLIGHT
Installation method and disassembly and replacement of embedded downlight | Square Recessed Downlights
At present, many living rooms are equipped with recessed downlights. However, it is inevitable to change the recessed downlight after a long time, but many people don't know what to do. Today, Houjiji will share with you how to install and disassemble the recessed downlight. Let's take a look at them.
1. Installation method of embedded downlight:
1. Check the indication of the embedded downlight, determine the size of the embedded downlight, and mark the opening position of the ceiling.
2. According to the size of the opening, use a measuring device to draw a circular mark on the ceiling and use a small hand saw to make the opening. This step requires a certain skill, otherwise it is easy to damage the ceiling.
3. Connect the power cord reserved on the ceiling to the recessed downlight according to the electricity specification.
4. Adjust the wing nut fixing the embedded downlight spring so that the height of the embedded downlight spring is equal to the thickness of the ceiling, and then put the embedded downlight spring buckle vertically into the open ceiling hole.
5. The spring buckles on both sides of the recessed downlight are extended and clamped on the back of the ceiling. Finally, replace the bulb to complete the installation of the embedded downlight.
How do I remove and replace the recessed downlight
1. When disassembling the electricity, disconnect the leakage switch and pay attention to the safety of electricity.
2. Remove the embedded downlight to prevent damage during removal.
3. According to the installation method of the embedded downlight mentioned above, it can be seen that the embedded downlight is fixed with a spring buckle and a barb, as long as the embedded downlight is pulled down and removed.
4. Disconnect the built-in downlight from the power supply, and replace the built-in downlight according to the above installation method.
Square Recessed Downlights
Installation method and disassembly and replacement of embedded downlight | Square Recessed Downlights
At present, many living rooms are equipped with recessed downlights. However, it is inevitable to change the recessed downlight after a long time, but many people don't know what to do. Today, Houjiji will share with you how to install and disassemble the recessed downlight. Let's take a look at them.
1. Installation method of embedded downlight:
1. Check the indication of the embedded downlight, determine the size of the embedded downlight, and mark the opening position of the ceiling.
2. According to the size of the opening, use a measuring device to draw a circular mark on the ceiling and use a small hand saw to make the opening. This step requires a certain skill, otherwise it is easy to damage the ceiling.
3. Connect the power cord reserved on the ceiling to the recessed downlight according to the electricity specification.
4. Adjust the wing nut fixing the embedded downlight spring so that the height of the embedded downlight spring is equal to the thickness of the ceiling, and then put the embedded downlight spring buckle vertically into the open ceiling hole.
5. The spring buckles on both sides of the recessed downlight are extended and clamped on the back of the ceiling. Finally, replace the bulb to complete the installation of the embedded downlight.
How do I remove and replace the recessed downlight
1. When disassembling the electricity, disconnect the leakage switch and pay attention to the safety of electricity.
2. Remove the embedded downlight to prevent damage during removal.
3. According to the installation method of the embedded downlight mentioned above, it can be seen that the embedded downlight is fixed with a spring buckle and a barb, as long as the embedded downlight is pulled down and removed.
4. Disconnect the built-in downlight from the power supply, and replace the built-in downlight according to the above installation method.
Square Recessed Downlights
Installation method and disassembly and replacement of embedded downlight | Square Recessed Downlights
At present, many living rooms are equipped with recessed downlights. However, it is inevitable to change the recessed downlight after a long time, but many people don't know what to do. Today, Houjiji will share with you how to install and disassemble the recessed downlight. Let's take a look at them.
1. Installation method of embedded downlight:
1. Check the indication of the embedded downlight, determine the size of the embedded downlight, and mark the opening position of the ceiling.
2. According to the size of the opening, use a measuring device to draw a circular mark on the ceiling and use a small hand saw to make the opening. This step requires a certain skill, otherwise it is easy to damage the ceiling.
3. Connect the power cord reserved on the ceiling to the recessed downlight according to the electricity specification.
4. Adjust the wing nut fixing the embedded downlight spring so that the height of the embedded downlight spring is equal to the thickness of the ceiling, and then put the embedded downlight spring buckle vertically into the open ceiling hole.
5. The spring buckles on both sides of the recessed downlight are extended and clamped on the back of the ceiling. Finally, replace the bulb to complete the installation of the embedded downlight.
How do I remove and replace the recessed downlight
1. When disassembling the electricity, disconnect the leakage switch and pay attention to the safety of electricity.
2. Remove the embedded downlight to prevent damage during removal.
3. According to the installation method of the embedded downlight mentioned above, it can be seen that the embedded downlight is fixed with a spring buckle and a barb, as long as the embedded downlight is pulled down and removed.
4. Disconnect the built-in downlight from the power supply, and replace the built-in downlight according to the above installation method.
Square Recessed Downlights
1. Installation method of embedded downlight:
1. Check the indication of the embedded downlight, determine the size of the embedded downlight, and mark the opening position of the ceiling.
2. According to the size of the opening, use a measuring device to draw a circular mark on the ceiling and use a small hand saw to make the opening. This step requires a certain skill, otherwise it is easy to damage the ceiling.
3. Connect the power cord reserved on the ceiling to the recessed downlight according to the electricity specification.
4. Adjust the wing nut fixing the embedded downlight spring so that the height of the embedded downlight spring is equal to the thickness of the ceiling, and then put the embedded downlight spring buckle vertically into the open ceiling hole.
5. The spring buckles on both sides of the recessed downlight are extended and clamped on the back of the ceiling. Finally, replace the bulb to complete the installation of the embedded downlight.
How do I remove and replace the recessed downlight
1. When disassembling the electricity, disconnect the leakage switch and pay attention to the safety of electricity.
2. Remove the embedded downlight to prevent damage during removal.
3. According to the installation method of the embedded downlight mentioned above, it can be seen that the embedded downlight is fixed with a spring buckle and a barb, as long as the embedded downlight is pulled down and removed.
4. Disconnect the built-in downlight from the power supply, and replace the built-in downlight according to the above installation method.
Square Recessed Downlights